Some resistors are long and thin, with the actual resisting part in the centre, with a conducting metal leg on each side. The photo on the right shows a row of commonly used resistors in a bandolier. Resistors used in computers and other devices are typically much smaller, often in surface-mount (Surface-mount technology) packages without leads.
Resistors are used as part of electrical networks and incorporated into microelectronic semiconductor devices. The critical measurement of a resistor is its resistance, which serves as a ratio of voltage to current and is measured by the SI unit ohm. A component has resistance 1 ohm if a voltage of 1 volt across the component results in a current of 1 ampere, or amp, which is equivalent to a flow of 6.25 × 1018 electrons per second in the opposite direction.
Any physical object is a kind of resistor. Most metals are conductors, and have low resistance to the flow of electricity. The human body, a piece of plastic, or even air has a resistance that can be measured. Materials that have very high resistance are called insulators.
The relationship between voltage, current, and resistance through an object is given by a simple equation, derived from and often confused with Ohm's Law:
Superconducting materials at very low temperatures have zero resistance. Insulators (such as air, diamond, or other non-conducting materials) may have extremely high (but not infinite) resistance, but break down and admit the flow of current under sufficiently high voltage.
The resistance of a component can be calculated from its physical characteristics. Resistance is proportional to the length of the resistor and to the material's resistivity, a physical property of the molecules that comprise the resistor, and inversely proportional to cross-sectional area.
Standard resistors are sold in values from a few milliohms to about a gigohm; only a limited range of values called preferred values are available. In practice, the discrete component sold as a "resistor" is not a perfect resistance, as defined above. Resistors are often marked with their tolerance (maximum expected variation from the marked resistance). On color coded resistors a rightmost silver band denotes 10% tolerance, a gold band 5% tolerance, and a red band 2% tolerance. Closer tolerance resistors, called precision resistors, are also available.
A resistor has a maximum working voltage and current above which the resistance may change (drastically, in some cases) or the resistor may be physically damaged (burn up, for instance). Although some resistors have specified voltage and current ratings, most are rated with a maximum power which is determined by the physical size. Common power ratings for carbon composition and metal-film resistors are 1/8 watt, 1/4 watt, and 1/2 watt. Metal-film resistors are more stable than carbon resistors against temperature changes and age. Larger resistors are able to dissipate more heat because of their larger surface area. Wire-wound and sand-filled resistors are used when a high power rating is required, such as 20 watts.
Furthermore, all real resistors also introduce some inductance and capacitance, which change the dynamic behavior of the resistor from the ideal equation.
Variable resistors can be cheap single-turn types or multi-turn types with a helical element. Some even have a mechanical display to count the turns.
Traditionally, variable resistors have been unreliable, because the wire or metal would corrode or wear. Some modern variable resistors use plastic materials that do not corrode. There is even a system that uses a photoelectric sensor "reading" the optical density of a piece of film. Since the sensor does not touch the film, no wear is possible.
A rheostat is a variable resistor with two terminals, one fixed and one sliding. It is often used with high currents.
A potentiometer is a common form of variable resistor. In this form, a movable contact called the wiper travels the length of a fixed resistor, both ends of the resistor as well as the wiper having electrical connections. This provides a variable ratio of resistances, as well as either an increasing or decreasing resistor. The resistive element may be resistance wire, carbon particles in plastic or a ceramic/metal mixture.
Although rotary potentiometers are more common, linear potentiometers also exist. It's often used to measure movement.
One popular form of rotary potentiometer is called a "string pot." It's a multi-turn potentiometer with an attached reel of wire turning against a spring. It's very convenient for measuring movement.
Potentiometers are available in both linear and logarithmic forms. A "linear pot" has a resistive element of constant cross-section, resulting in a device where the resistance between the wiper and one end terminal is proportional to the distance between them. A "log pot" has a resistive element that either tapers in a controlled way from one end to the other, or is made from a material whose resistivity varies from one end to the other. This results in a device where the distance between the wiper and one end terminal is proportional to the logarithm of the resistance between them. The "log pot" is used as the volume control in audio amplifiers, where it is also called an "audio pot", because the amplitude response of the human ear is also logarithmic. It ensures that, on a volume control marked 0 to 10, for example, a setting of 5 sounds half as loud as a setting of 10.
A Metal Oxide Varistor, or M.O.V. is a special type of resistor which has 2 very different resistance values, a very high resistance at low voltage (below the trigger voltage) and very low resistance at high voltage (above the trigger voltage). They are usually used for short circuit protection in power strips or lightning bolt "arrestors" on street power poles, or as a "snubber"
in back electromotive force circuits.
Variable resistor
The variable resistor is a resistor whose value can be adjusted by a mechanical movement, for example by being turned by hand. See Also
Resistors in series and parallel circuits
Electronic color code\n